Comments on: Make Your Own Limb Risers https://www.overlandbound.com/make-your-own-limb-risers/ Outfit & Explore Fri, 24 Jun 2022 00:25:44 +0000 hourly 1 https://wordpress.org/?v=6.4.3 By: Part 8 – Light Bar, Molle Packs and Limb Risers – BROx4 https://www.overlandbound.com/make-your-own-limb-risers/#comment-395 Thu, 13 Sep 2018 13:41:54 +0000 http://overlandbound.com/?p=17548#comment-395 […] watched @Michael‘s video of how to make your own and it looked pretty easy. Pretty sure I can accomplish […]

]]> By: jcaliri https://www.overlandbound.com/make-your-own-limb-risers/#comment-394 Tue, 23 May 2017 23:36:36 +0000 http://overlandbound.com/?p=17548#comment-394 Very nice video and information. Seems like one of those tings that any one can figure out but there you have done it already for us. Thanks, nice work!

]]> By: Duncan Lee https://www.overlandbound.com/make-your-own-limb-risers/#comment-393 Sun, 05 Mar 2017 18:10:19 +0000 http://overlandbound.com/?p=17548#comment-393 Not to be over critical, but drilling a hole on top of roof rack will allow water to enter the tube causing internal rusting. Drill horizontally into tube, or fill hole with good silicone to seal it.There are also tubing clamps that can used without drilling. Cables still don’t protect the two way radio aerial. No solution there that I know of unless you mount the aerial back near the windshield. I’m sure there is a reason for mounting it on the brush bar.

]]> By: Michael Collins https://www.overlandbound.com/make-your-own-limb-risers/#comment-392 Sat, 25 Jul 2015 08:43:10 +0000 http://overlandbound.com/?p=17548#comment-392 In reply to Jason Wellman.

Jason,
I have the ARB front bumper, but without headlight guards. Could you provide more info on your solution? Thank you.
Mike Collins
San Diego, CA

]]> By: Jason Wellman https://www.overlandbound.com/make-your-own-limb-risers/#comment-391 Sat, 25 Jul 2015 06:08:49 +0000 http://overlandbound.com/?p=17548#comment-391 In reply to Randy.

You could always drill the roof and add a backing plate under the headliner to mount a stud or eye bolt

]]> By: Randy https://www.overlandbound.com/make-your-own-limb-risers/#comment-390 Fri, 24 Jul 2015 21:56:54 +0000 http://overlandbound.com/?p=17548#comment-390 In reply to Jason Wellman.

I have a front mounting point but no roof rack so working on a solution at that end.

]]> By: Jason Wellman https://www.overlandbound.com/make-your-own-limb-risers/#comment-389 Fri, 24 Jul 2015 21:35:37 +0000 http://overlandbound.com/?p=17548#comment-389 i just made my own yesterday before this was posted.

an easy way to make a front mounting point if you dont have a bumper with headlight guards is to use a couple of antenna mounts for a hood channel.

]]> By: Randy https://www.overlandbound.com/make-your-own-limb-risers/#comment-388 Fri, 24 Jul 2015 17:50:44 +0000 http://overlandbound.com/?p=17548#comment-388 No issues w/ the roof rack sliding forward if you hit anything a bit too robust? Any thoughts on how to mount the top edge if not using a roof rack?

]]>